Carrol Touch Modular Flat Panel Specifications Page 121
- Page / 274
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Appendix A - Smart-Frame Protocol Command Reference CARROLL TOUCH
A-12 Touch System Programmer’s Guide
Enter_Point_Mode (25H) (%)
Command Description
When the touch mode is set to Enter Point Mode by sending the
Enter_Point_Mode (25H) command, the touch system sends a Touch
Coordinate Report to the host when the stylus enters the touch active
area. No additional Touch Coordinate Reports are transmitted until an
empty scan (no stylus located within the touch active area) is detected,
indicating that the stylus has left the touch active area. Enter Point
Mode is most commonly used to select a sequence of items on a single
menu or when an immediate response is required.
Report Format
See Coordinate Reporting (23H) in this appendix for the format of the
Touch Coordinate Report and Non-Contiguous Coordinate Report.
Example
See Coordinate Reporting (23H) in this appendix for examples of the
Touch Coordinate Report and Non-Contiguous Coordinate Report.
See Also
Coordinate_Reporting (23H)
- TouchSystem 1
- Programmer's 1
- Touch System 2
- Programmer’s 2
- Table of Contents 4
- List of Figures 10
- List of Tables 12
- WelcomeWelcome 14
- Welcome CARROLL TOUCH 15
- Conventions 16
- Overview 19
- Touch Frames 19
- Touch Controller 19
- Reporting Touch Coordinates 21
- Failed Beams 21
- Criteria for Failing a Beam 22
- Failed Beam Timing Parameters 22
- Criteria for Unfailing a Beam 24
- Failed Beam Reports 24
- Touch Screens 27
- Touch Controllers 27
- EEPROM File and Parameters 28
- • Hardware Configurations 30
- • Calibration 30
- • HBC I/O Registers 30
- Hardware Configurations 31
- Application Program Interface 33
- Calibration 35
- HBC I/O Registers 38
- Polling Mode 39
- Resetting the HBC 40
- Smart-Frame 42
- Protocol 42
- SFP and SFP-II 43
- Types of SFP Commands 43
- Communication Commands 44
- Reporting Method Commands 44
- Touch Mode Commands 45
- Information Request Commands 46
- System Commands 46
- Touch System Initialization 48
- Sequence 49
- Using Autobaud/Autoparity 51
- Using a Fixed Baud Rate 52
- Using the HBC 52
- Using an SBC 53
- Firmware Version Independence 54
- Frame Size Independence 54
- Touch System Response Time 54
- Independence 54
- SFP Timing 55
- SFP Programming Examples 55
- Protocol II 58
- Modal Protocols 61
- Backward Compatibility 61
- Types of SFP-II Functions 62
- Functions 62
- Commands 63
- Validation Layer 64
- Interpretation Layer 64
- Reporting Modes 68
- Report Transfer Mode 68
- Error Reporting 69
- Invalid Parameter Value 70
- Unsupported Feature 70
- Invalid Byte Count 71
- Not Enough Parameters 74
- Too Many Parameters 74
- Overloaded Functions 75
- Touch Detection 76
- Report Transfer 77
- Installing a TAPI Driver 80
- HBC Driver 81
- RS-232 Driver 81
- Error Messages 83
- Calling TAPI Functions 84
- TAPI Programming Examples 86
- Touch Reporting 92
- Disabled 94
- Automatic 94
- Temporal Filter 95
- Loading the CTKERN Driver 96
- Calling CTKERN Functions 100
- CALIB.EXE 100
- Command Line 101
- Operation 102
- Calibrate Other Video Modes 104
- Delete Entry 105
- Edit Entry 105
- SC key from 106
- CALIB.DAT 107
- CTKERN Programming Examples 107
- Command Description 114
- Report Format 114
- See Also 114
- Continuous_Mode (27H) (’) 116
- Echo_Off (21H) (!) 119
- Echo_On (20H) (SPACE) 120
- Enter_Point_Mode (25H) (%) 121
- Exit_Point_Mode (28H) (() 122
- Get_Error_Report (32H) (2) 124
- Get_One_Report (46H) (F) 133
- Get_State_Report (47H) (G) 134
- Report_Transfer_Off (43H) (C) 138
- Report_Transfer_On (44H) (D) 139
- Reset (45H) (E) 140
- Run_Diagnostics (3AH) (:) 141
- Scan_Reporting (22H) (”) 142
- Software_Reset (3CH) (<) 143
- SwitchToSFP-II (65H) 144
- Touch_Scanning_Off (2BH) (+) 146
- Touch_Scanning_On (2AH) (*) 147
- Tracking_Mode (26H) (&) 148
- GetConfiguration (11H) 152
- Command Format 153
- Report Description 153
- Examples 155
- GetCoordinateRanges (10H) 157
- GetProtocolVersion (65H) 159
- GetTouchState (01H) 161
- SetReportProperties (21H) 163
- SetReportTransferMode (22H) 168
- SetTouchModes (20H) 173
- SwitchToClassicSFP (64H) 178
- TAPI Function 180
- Reference 180
- CheckForReports (3) 182
- Description 183
- Call with 183
- GetReports (2) 185
- Reset (0) 188
- SendCommand (1) 189
- SetSBCFrameSize (40H) 192
- SetUserEventHandler (7) 193
- • SetTouchState (2) 197
- • SetZ-AxisScalingMode (11) 197
- GetTouchState (1) 208
- GetReport (18) 215
- SetCalibrationMode (3) 217
- SetCalibrationParameters (4) 218
- SetCalibrationTableEntry (6) 219
- SetScalingMode (8) 223
- SetScalingParameters (9) 224
- SetTemporalFilterMode (14) 226
- box size 227
- SetTouchState (2) 231
- SetUserEventHandlerMode (23) 232
- SetZ-AxisScalingMode (11) 235
- DisableMouse (11) 240
- DisableTouch (12) 241
- EnableMouse (9) 242
- EnableTouch (10) 243
- GetMouseInfo (13) 244
- GetTemporalFilterInfo (18) 245
- GetTouchInfo (14) 246
- GetTouchStateandCoord (5) 247
- InitializeTouch (16) 248
- SetCalibInfo (7) 249
- Function Call 250
- SetTemporalFilterInfo (17) 251
- SetTouchEvents (8) 253
- Glossary 254
- Glossary CARROLL TOUCH 255
- CARROLL TOUCH Glossary 256
- CARROLL TOUCH Index 260
- Index CARROLL TOUCH 261
- CONTACTING CARROLL TOUCH: 274
© 2020, manymanuals.com. All rights reserved. | 2.649 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals