Carrol Touch Modular Flat Panel Specifications Page 81
- Page / 274
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 6 - Touch Application Program Interface (TAPI) CARROLL TOUCH
6-4 Touch System Programmer’s Guide
HBC Driver
If you have set the I/O address or the interrupt number parameters of
the HBC to values other than the default parameters, you must provide
the correct values for these parameters on the command line when
installing the HBC driver.
The HBC driver command line has the following syntax:
HBC options
The available options are:
U = Uninstalls the driver.
An = I/O address. n may range from 200H to 3F0H. The
default is 300H.
In = Interrupt number. n may be 2, 3, 4, 5, or 7. The default
is 7.
Sn = TAPI software interrupt. n may be the number of any
unused software interrupt. The default is 55H.
The command line is case insensitive and the command line parameters
may be arranged in any order. For example, to install an HBC driver
using an I/O address of 340H, hardware interrupt 2, and software
interrupt 57H, you can type either:
HBC A340 I2 S57
or
hbc i2 a340 s57
RS-232 Driver
If you have set the baud rate or parity parameters of the RS-232
controller board to values other than the default values of
autobaud/autoparity, or if you are using an RS-232 port other than the
default value of COM1, you must provide the correct values for these
parameters on the command line when installing the RS-232 driver.
The RS-232 driver command line has the following syntax:
RS232 options
The available options are:
- TouchSystem 1
- Programmer's 1
- Touch System 2
- Programmer’s 2
- Table of Contents 4
- List of Figures 10
- List of Tables 12
- WelcomeWelcome 14
- Welcome CARROLL TOUCH 15
- Conventions 16
- Overview 19
- Touch Frames 19
- Touch Controller 19
- Reporting Touch Coordinates 21
- Failed Beams 21
- Criteria for Failing a Beam 22
- Failed Beam Timing Parameters 22
- Criteria for Unfailing a Beam 24
- Failed Beam Reports 24
- Touch Screens 27
- Touch Controllers 27
- EEPROM File and Parameters 28
- • Hardware Configurations 30
- • Calibration 30
- • HBC I/O Registers 30
- Hardware Configurations 31
- Application Program Interface 33
- Calibration 35
- HBC I/O Registers 38
- Polling Mode 39
- Resetting the HBC 40
- Smart-Frame 42
- Protocol 42
- SFP and SFP-II 43
- Types of SFP Commands 43
- Communication Commands 44
- Reporting Method Commands 44
- Touch Mode Commands 45
- Information Request Commands 46
- System Commands 46
- Touch System Initialization 48
- Sequence 49
- Using Autobaud/Autoparity 51
- Using a Fixed Baud Rate 52
- Using the HBC 52
- Using an SBC 53
- Firmware Version Independence 54
- Frame Size Independence 54
- Touch System Response Time 54
- Independence 54
- SFP Timing 55
- SFP Programming Examples 55
- Protocol II 58
- Modal Protocols 61
- Backward Compatibility 61
- Types of SFP-II Functions 62
- Functions 62
- Commands 63
- Validation Layer 64
- Interpretation Layer 64
- Reporting Modes 68
- Report Transfer Mode 68
- Error Reporting 69
- Invalid Parameter Value 70
- Unsupported Feature 70
- Invalid Byte Count 71
- Not Enough Parameters 74
- Too Many Parameters 74
- Overloaded Functions 75
- Touch Detection 76
- Report Transfer 77
- Installing a TAPI Driver 80
- HBC Driver 81
- RS-232 Driver 81
- Error Messages 83
- Calling TAPI Functions 84
- TAPI Programming Examples 86
- Touch Reporting 92
- Disabled 94
- Automatic 94
- Temporal Filter 95
- Loading the CTKERN Driver 96
- Calling CTKERN Functions 100
- CALIB.EXE 100
- Command Line 101
- Operation 102
- Calibrate Other Video Modes 104
- Delete Entry 105
- Edit Entry 105
- SC key from 106
- CALIB.DAT 107
- CTKERN Programming Examples 107
- Command Description 114
- Report Format 114
- See Also 114
- Continuous_Mode (27H) (’) 116
- Echo_Off (21H) (!) 119
- Echo_On (20H) (SPACE) 120
- Enter_Point_Mode (25H) (%) 121
- Exit_Point_Mode (28H) (() 122
- Get_Error_Report (32H) (2) 124
- Get_One_Report (46H) (F) 133
- Get_State_Report (47H) (G) 134
- Report_Transfer_Off (43H) (C) 138
- Report_Transfer_On (44H) (D) 139
- Reset (45H) (E) 140
- Run_Diagnostics (3AH) (:) 141
- Scan_Reporting (22H) (”) 142
- Software_Reset (3CH) (<) 143
- SwitchToSFP-II (65H) 144
- Touch_Scanning_Off (2BH) (+) 146
- Touch_Scanning_On (2AH) (*) 147
- Tracking_Mode (26H) (&) 148
- GetConfiguration (11H) 152
- Command Format 153
- Report Description 153
- Examples 155
- GetCoordinateRanges (10H) 157
- GetProtocolVersion (65H) 159
- GetTouchState (01H) 161
- SetReportProperties (21H) 163
- SetReportTransferMode (22H) 168
- SetTouchModes (20H) 173
- SwitchToClassicSFP (64H) 178
- TAPI Function 180
- Reference 180
- CheckForReports (3) 182
- Description 183
- Call with 183
- GetReports (2) 185
- Reset (0) 188
- SendCommand (1) 189
- SetSBCFrameSize (40H) 192
- SetUserEventHandler (7) 193
- • SetTouchState (2) 197
- • SetZ-AxisScalingMode (11) 197
- GetTouchState (1) 208
- GetReport (18) 215
- SetCalibrationMode (3) 217
- SetCalibrationParameters (4) 218
- SetCalibrationTableEntry (6) 219
- SetScalingMode (8) 223
- SetScalingParameters (9) 224
- SetTemporalFilterMode (14) 226
- box size 227
- SetTouchState (2) 231
- SetUserEventHandlerMode (23) 232
- SetZ-AxisScalingMode (11) 235
- DisableMouse (11) 240
- DisableTouch (12) 241
- EnableMouse (9) 242
- EnableTouch (10) 243
- GetMouseInfo (13) 244
- GetTemporalFilterInfo (18) 245
- GetTouchInfo (14) 246
- GetTouchStateandCoord (5) 247
- InitializeTouch (16) 248
- SetCalibInfo (7) 249
- Function Call 250
- SetTemporalFilterInfo (17) 251
- SetTouchEvents (8) 253
- Glossary 254
- Glossary CARROLL TOUCH 255
- CARROLL TOUCH Glossary 256
- CARROLL TOUCH Index 260
- Index CARROLL TOUCH 261
- CONTACTING CARROLL TOUCH: 274
© 2020, manymanuals.com. All rights reserved. | 0.951 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals