Carrol Touch Modular Flat Panel Specifications Page 124
- Page / 274
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CARROLL TOUCH Appendix A - Smart-Frame Protocol Command Reference
Touch System Programmer’s Guide A-15
Get_Error_Report (32H) (2)
Command Description
When the host sends the Get_Error_Report (32H) command, the touch
system returns an Error Report, which identifies the current error
conditions.
Report Format
For single-processor systems, the Error Report has the following
format:
F8 Na Aa, ..., An FF
For dual-processor systems, the Error Report has the following format:
F8 Na Aa, ..., An Nb Ba, ..., Bn FF
F8 = Start of Error Report.
Na = Number of first processor errors to follow.
Aa, ..., An
= Error codes (defined in Table A-3).
Nb = Number of second processor errors to follow.
Ba, ..., Bn
= Error codes (defined in Table A-3).
FF = End of report.
If the touch system does not detect any errors, the following report is
sent:
F8 00 FF Reports no errors for single-processor systems.
F8 00 00 FF Reports no errors for dual-processor systems.
The Error Report contains a list of error codes for each processor in the
touch system. Use the Get_Configuration_Report (33H) command to
get a Configuration Report that includes the number of processors in
the touch system in order to properly interpret this report.
- TouchSystem 1
- Programmer's 1
- Touch System 2
- Programmer’s 2
- Table of Contents 4
- List of Figures 10
- List of Tables 12
- WelcomeWelcome 14
- Welcome CARROLL TOUCH 15
- Conventions 16
- Overview 19
- Touch Frames 19
- Touch Controller 19
- Reporting Touch Coordinates 21
- Failed Beams 21
- Criteria for Failing a Beam 22
- Failed Beam Timing Parameters 22
- Criteria for Unfailing a Beam 24
- Failed Beam Reports 24
- Touch Screens 27
- Touch Controllers 27
- EEPROM File and Parameters 28
- • Hardware Configurations 30
- • Calibration 30
- • HBC I/O Registers 30
- Hardware Configurations 31
- Application Program Interface 33
- Calibration 35
- HBC I/O Registers 38
- Polling Mode 39
- Resetting the HBC 40
- Smart-Frame 42
- Protocol 42
- SFP and SFP-II 43
- Types of SFP Commands 43
- Communication Commands 44
- Reporting Method Commands 44
- Touch Mode Commands 45
- Information Request Commands 46
- System Commands 46
- Touch System Initialization 48
- Sequence 49
- Using Autobaud/Autoparity 51
- Using a Fixed Baud Rate 52
- Using the HBC 52
- Using an SBC 53
- Firmware Version Independence 54
- Frame Size Independence 54
- Touch System Response Time 54
- Independence 54
- SFP Timing 55
- SFP Programming Examples 55
- Protocol II 58
- Modal Protocols 61
- Backward Compatibility 61
- Types of SFP-II Functions 62
- Functions 62
- Commands 63
- Validation Layer 64
- Interpretation Layer 64
- Reporting Modes 68
- Report Transfer Mode 68
- Error Reporting 69
- Invalid Parameter Value 70
- Unsupported Feature 70
- Invalid Byte Count 71
- Not Enough Parameters 74
- Too Many Parameters 74
- Overloaded Functions 75
- Touch Detection 76
- Report Transfer 77
- Installing a TAPI Driver 80
- HBC Driver 81
- RS-232 Driver 81
- Error Messages 83
- Calling TAPI Functions 84
- TAPI Programming Examples 86
- Touch Reporting 92
- Disabled 94
- Automatic 94
- Temporal Filter 95
- Loading the CTKERN Driver 96
- Calling CTKERN Functions 100
- CALIB.EXE 100
- Command Line 101
- Operation 102
- Calibrate Other Video Modes 104
- Delete Entry 105
- Edit Entry 105
- SC key from 106
- CALIB.DAT 107
- CTKERN Programming Examples 107
- Command Description 114
- Report Format 114
- See Also 114
- Continuous_Mode (27H) (’) 116
- Echo_Off (21H) (!) 119
- Echo_On (20H) (SPACE) 120
- Enter_Point_Mode (25H) (%) 121
- Exit_Point_Mode (28H) (() 122
- Get_Error_Report (32H) (2) 124
- Get_One_Report (46H) (F) 133
- Get_State_Report (47H) (G) 134
- Report_Transfer_Off (43H) (C) 138
- Report_Transfer_On (44H) (D) 139
- Reset (45H) (E) 140
- Run_Diagnostics (3AH) (:) 141
- Scan_Reporting (22H) (”) 142
- Software_Reset (3CH) (<) 143
- SwitchToSFP-II (65H) 144
- Touch_Scanning_Off (2BH) (+) 146
- Touch_Scanning_On (2AH) (*) 147
- Tracking_Mode (26H) (&) 148
- GetConfiguration (11H) 152
- Command Format 153
- Report Description 153
- Examples 155
- GetCoordinateRanges (10H) 157
- GetProtocolVersion (65H) 159
- GetTouchState (01H) 161
- SetReportProperties (21H) 163
- SetReportTransferMode (22H) 168
- SetTouchModes (20H) 173
- SwitchToClassicSFP (64H) 178
- TAPI Function 180
- Reference 180
- CheckForReports (3) 182
- Description 183
- Call with 183
- GetReports (2) 185
- Reset (0) 188
- SendCommand (1) 189
- SetSBCFrameSize (40H) 192
- SetUserEventHandler (7) 193
- • SetTouchState (2) 197
- • SetZ-AxisScalingMode (11) 197
- GetTouchState (1) 208
- GetReport (18) 215
- SetCalibrationMode (3) 217
- SetCalibrationParameters (4) 218
- SetCalibrationTableEntry (6) 219
- SetScalingMode (8) 223
- SetScalingParameters (9) 224
- SetTemporalFilterMode (14) 226
- box size 227
- SetTouchState (2) 231
- SetUserEventHandlerMode (23) 232
- SetZ-AxisScalingMode (11) 235
- DisableMouse (11) 240
- DisableTouch (12) 241
- EnableMouse (9) 242
- EnableTouch (10) 243
- GetMouseInfo (13) 244
- GetTemporalFilterInfo (18) 245
- GetTouchInfo (14) 246
- GetTouchStateandCoord (5) 247
- InitializeTouch (16) 248
- SetCalibInfo (7) 249
- Function Call 250
- SetTemporalFilterInfo (17) 251
- SetTouchEvents (8) 253
- Glossary 254
- Glossary CARROLL TOUCH 255
- CARROLL TOUCH Glossary 256
- CARROLL TOUCH Index 260
- Index CARROLL TOUCH 261
- CONTACTING CARROLL TOUCH: 274
© 2020, manymanuals.com. All rights reserved. | 0.973 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals